ECUTools International

  • Home
  • ECUTools International

ECUTools International ECUTools International is a page of ecutools.eu chip-tuning and diagnostics equipment shop.

❗️ M&D flasher license for GM ACDelco E37/E38 is open for pre-order! ❗️✅ PRE-ORDER License 90 — GM ACDelco E37/E38 ECU B...
05/10/2022

❗️ M&D flasher license for GM ACDelco E37/E38 is open for pre-order! ❗️
✅ PRE-ORDER License 90 — GM ACDelco E37/E38 ECU BENCH/OBDII is up!
The module works with ACDelco E37/E38 in OBDII Mode or Bench Mode.
➡️ 1. OBDII Mode (working in the vehicle):
✅ Identification
✅ Error reading
✅ Error reset
✅ Flash reading
✅ Calibration area writing (without checksum corrections)
➡️ 2. Bench Mode:
✅ Flash reading
✅ Flash writing (without checksum corrections)
✅ EEPROM reading
✅ EEPROM writing
Not all software versions may be supported.
⭐️ The activation files will be sent within a week after 03.05.2022
https://ecutools.eu/.../license-90-gm-acdelco-e37-e38.../

❗️ K-TAG and KESSv2 special offers! ❗️⭐️ Starting today until April 3rd inclusive, K-TAG and Kess v2 users have special ...
05/10/2022

❗️ K-TAG and KESSv2 special offers! ❗️
⭐️ Starting today until April 3rd inclusive, K-TAG and Kess v2 users have special offers for subscription renewals.
To receive an individual offer please contact us via email: [email protected]
K-TAG Master: https://ecutools.eu/chip-tuning/alientech-k-tag-master/
K-TAG Slave: https://ecutools.eu/chip-tuning/alientech-k-tag-slave/
KESS Master: https://ecutools.eu/chip-tuning/alientech-kess-ii-master/
KESS Slave: https://ecutools.eu/chip-tuning/alientech-kess-ii-slave/

❗️ New tools in our catalog: DFOX Master and Slave! ❗️⭐️ DFOX from DFB TECHNOLOGY allows serial communication with the E...
05/10/2022

❗️ New tools in our catalog: DFOX Master and Slave! ❗️
⭐️ DFOX from DFB TECHNOLOGY allows serial communication with the Engine and Automatic transmission control units via the OBD diagnostic socket. It is a professional software for reading and programming the control units of:
✅ Cars
✅ Trucks
✅ Motorbikes
✅ Tractors
✅ Boats
✅ Additional TCU package available for Automatic Transmissions
➡️ It also allows communication in the following modes:
✅ BDM and JTAG
✅ BOOT Mode
✅ BENCH Mode (or Service mode)
✅ FULL SYSTEM via pinout
➡️ Compatible operating systems:
✅ Windows 7
✅ Windows 8/8.1
✅ Windows 10
✅ Windows 11!
➡️ Minimum recommended requirements:
CPU > 2.5 GHz (Intel i5, i7)
RAM > 4GB
The tool has annual subscription, though it is not mandatory for working.
ECUTools are the first and only dealer of DFB TECHNOLOGY in Russia!
➡️ DFOX Master (https://ecutools.eu/chip-tuning/dfox-master/)
➡️ DFOX Slave (https://ecutools.eu/chip-tuning/dfox-slave/)

⭐️❗️ PCMflash Update! ❗️ ⭐️New modules and additions to the current protocols in PCMflash (https://ecutools.eu/chip-tuni...
05/10/2022

⭐️❗️ PCMflash Update! ❗️ ⭐️
New modules and additions to the current protocols in PCMflash (https://ecutools.eu/chip-tuning/pcmflash/)!
✅ Module 82 (https://ecutools.eu/chip-tuning/pcmflash/module-82/): Bosch SH725XX TCU Bootloader, designed to work in service mode (on the bench) with Bosch TCUs with SH725xx microcontrollers, available in ZF 8HP, VAG DQ380/381/500, MEG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. Supports Flash and EEPROM reading, writing, checksum corrections.
✅ Module 83 (https://ecutools.eu/chip-tuning/pcmflash/module-83/): VAG Bosch DQ380/DQ381/DQ500/ZF 8HP, designed to work via the diagnostic connector with DSG and automatic transmission units used in VAG vehicles. Reading (virtual), writing, checksum corrections.
✅ Module 84 (https://ecutools.eu/chip-tuning/pcmflash/module-84/): VAG Delphi DCM6.2 supports working via the diagnostic connector of VAG vehicles with Delphi DCM6.2 ECUs. Supports virtual reading, writing, checksum corrections.
✅ Module 85 (https://ecutools.eu/chip-tuning/pcmflash/module-85/): Ford Gearbox is designed for working via the diagnostic connector with 6HP28, 5R/6R/6 °F/8 °F/10R TCUs of various modifications used in Ford vehicles. Reading, writing and checksum corrections is supported.
➡️ Updates for the existing modules can be found here (https://ecutools.eu/publications/pcmflash-update-21022022/) ⬅️

Address

Harju Maakond, Kesklinna Linnaosa, Narva Mnt 7-634

Telephone

+79215399354

Website

Alerts

Be the first to know and let us send you an email when ECUTools International posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to ECUTools International:

Shortcuts

  • Address
  • Telephone
  • Alerts
  • Contact The Business
  • Claim ownership or report listing

  • Want your business to be the top-listed Media Company?

Share